RDL Technologies Pvt.Ltd
USB To RS232 Converter

USB To RS232 Converter

Few older devices use DB9 connectors, but most modern computers use USB  port for data transfer. By using a USB to serial adapter, you can continue to use your older serial-enabled device through your new computer's USB port. These cables are also referred to as USB to DB9 or or USB to RS-232 cables.USB to serial adapters are cables that convert the data sent by a serial-enabled device for use by a USB port. The serial end has a DB9 connector, which plugs into the serial device. The USB connector plugs into the computer's USB port or a connected USB hub. The data that are transmitted by the serial device are sent directly to the USB port, where it is passed to software to interpret it.

 Order Code : RDL/U2U/13/001/V1.0

The FT232R is the latest device to be added to FTDI's range of USB UART interface Integrated Circuit Devices. The FT232R is a USB to serial UART interface with optional clock generator output, and the new FTDIChip-ID™ security dongle feature. In addition, asynchronous and synchronous bit bang interface modes are available. USB to serial designs using the FT232R have been further simplified by fully integrating the external EEPROM, clock circuit and USB resistors onto the device.

Features:

  • Single board USB to asynchronous serial data transfer interface. 
  • UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd/ even/ mark/ space/ no parity. 
  • Power LED. 
  • 12MHz clock output signal for driving external MCU or FPGA. 
  • Low USB bandwidth consumption. 
  • Supports automatic handshake mode
  • Supports Remote wake-up and power management
  • 256-bytes buffer each for upstream and downstream data flow
  • Supports Windows 98/SE, ME, 2000, XP, Windows CE3.0, CE .NET, Linux, and Mac OS 
  • High quality PCB FR4 Grade with FPT Certified.

FT232RL IC Features:

  • Single chip USB to asynchronous serial data transfer interface.
  •  Entire USB protocol handled on the chip. No USB specific firmware programming required.
  • Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
  • Fully integrated USB termination resistors.
  • Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
  • Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232 ) at TTL levels.
  • 128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
  • FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
  • Unique USB FTDIChip-ID™ feature.
  •  Configurable CBUS I/O pins.
  • Transmit and receive LED drive signals.
  •  UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no paritySingle chip USB to asynchronous serial data transfer interface.
  • Entire USB protocol handled on the chip. No USB specific firmware programming required.
  • Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
  • Fully integrated USB termination resistors.
  • Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
  • Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232 ) at TTL levels.
  • 128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
  •  FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
  • Unique USB FTDIChip-ID™ feature.
  • Configurable CBUS I/O pins.
  • Transmit and receive LED drive signals.
  • UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity

Package Contains :

  • USB To RS232 Converter.
Documents:

785.00 623.00

Reviews